Free db2 antenna software for windows

Satellite Antenna Alignment 2.60.0.0 is a professional and smart program which is used to calculate the angles necessary for installing satellite dishes. The main difference from similar software is the possibility to calculate the position for all satellites at once. Thus, you get a clear picture about what satellites can be physically visible from the location where the dish will be installed. Additionally, the program has a mechanism for calculating the azimuth of the sun and you can do everything without a compass now!

You should start working with the program from entering the geographical coordinates of the location where you are going to install the satellite dish. Enter your coordinates in the "Site location" box. The high latitude is specified with the "N" char, the low latitude is specified with the the "S" char. Similarly, the eastern longitude is with the "E" char, while the western longitude is with the "W" char. After all the coordinates are entered, you will see the calculation for all satellites at once in the table to the left. Their azimuth and elevation are calculated. Azimuth is the direction to the satellite in degrees from the clockwise direction to the north. Elevation is an angle (measured in degrees) between the direction of the signal from the satellite and a tangential plane to the Earth surface in the location. If the elevation is negative, the satellite is below the horizon and it is impossible to receive signals from it in principle. Thus, the satellites whose elevation is a positive value are theoretically visible from your location. If you know the azimuth, you can quickly find the direction to the satellite and see what obstacles (neighboring houses, trees) there are in the way of the signal from the satellite to your dish.

Both the azimuth and the elevation are calculated for the sun for the current moment of time. Thus, you can install the satellite dish without a compass at all. First, find the azimuth of the satellite you need. Then calculate the azimuth of the sun for the day on which you are going to install the dish. Find the azimuth of the sun that is most close to the azimuth to the satellite and you will see the time (and date) when the sun will be in the same direction where the satellite is. Turn the dish to the sun at the specified moment of time, the azimuth of the sun coincides with the azimuth of the satellite at this moment. Or just note this direction and install the dish later. Remember to specify your time zone for calculation (Moscow: +3 GMT). The program also calculates the azimuths of the sunrise and sunset, as well as the time and elevation when the sun is exactly in the south.

Major Features:

1. Uses absolute values and calculates everything according to formulas. Thus, the calculated azimuth is an angle from the true north and not from what your compass may show because a compass is a really unstable thing, especially in a city. It is better to orient it by the sun
   
2. Has a mechanism for calculating the azimuth of the sun and you can do everything without a compass
3. The azimuth is calculated for the location the coordinates of which you specified for calculating the azimuths of satellites.
4. You can specify the date (the current date is taken by default) and calculate how the sun moves with a one minute discontinuity.
5. The calculation results are displayed in the table to the left.
6. Draws a simple diagram representing the four directions. The yellow sector is daytime, its eastern part is sunrise and its western part is sunset.
7. The same diagram can be used to schematically represent the direction to the satellite you need. Select the satellite from the drop-down list and the red line will show the direction to it (azimuth). If the elevation is negative, no red line is drawn (the satellite is not visible).
8. Offset satellite dishes are widely spread now.
9. When such a dish is completely vertical, it already has some elevation (~20-25 degrees).
10. You can enter the size of your offset dish (height and width) and the program will calculate the exact elevation for this dish.
11. The calculation is done only for dishes whose height is greater than width. Enter the size of the dish in millimeters. Here you will see the elevation to the selected satellite and the angle you should actually install you dish at (in degrees from the Earth surface).
    

Requirements: Pentium

WareSeeker Editor

TOAD for DB2 4.0.1.921 provides an integrated toolset that improves productivity, database performance and application availability.

TOAD for DB2 is a database development solution that provides productivity features/functions for rapidly creating and executing queries, facilitating database object management, developing SQL code, and instant access to DB2 expertise.

Developers have access to a community of users, peers, and experts to help solve development issues and assist in developing applications and feedback for improving Quests products.

All of this comes with the backing of Quest Software, a healthy and growing corporate entity that can provide the necessary training, support, and superior customer service demanded by IT management.

Major Features:

1. Minimizes development and administration costs by automating common tasks
2. Reduces the DB2 LUW database total cost of ownership and decreases development cycles by helping to resolve problems before end users are impacted
3. Lowers the risk of slow transaction response time and downtime, enabling you to meet service level agreements (SLAs)
4. Ensures that new applications meet business requirements and perform well in production
5. Object Management with the Toad DBA Suite for DB2 LUW
6. Spotlight on DB2 LUW Performance Diagnostics
7. SQL Optimizer for IBM DB2

Requirements:

1. Microsoft .NET
2. Framework version 2.0