Free virtual serial port control software for windows

Lalim Parallel Port Control can control hardware through the parallel port (printer port) and can also control a remote PC parallel port through a network.
Most of engineering industry using PC to control hardware with using additional I/O card but with Lalim Parallel Port Control you can use your default printer port controlling external device such as switching on/off light or control electronic devices.
What does this program [does is] trigger the parallel port (Printer port) s data pin by your command. For example when you trigger pin2, your printer ports pin2 becomes +5 volt.
With this +5 volt, you can build your own electronic circuit to drive other external device. You can also built a simple circuit to test it by connect a LED with 1 kohm resistor direct to it pin.
Lalim Parallel Port Control requires a certain knowledge of electronics and if you are not comfortable with a soldering iron, or dont know what a 1k resistor is, then it is probably advisable that you do not attempt to use this program.
If you are capable working with DC electronics, Lalim Parallel Port Control allows you to build remote-controlled, or timed, devices for your home or office ? turning on or off the air conditioner, adjusting lighting, opening & closing windows, monitoring burglar alarms, and more.

HiSerial.sys Serial Port Driver is a replacment for Microsoft's Serial.sys serial port driver. HiSerial.sys does enable high speed serial communication up to 921600 baud on both serial ports. The possibility of speeds higher than 115200 baud depends on the computers chipset. Version 1.5 may include unspecified updates, enhancements, or bug fixes.

A software application that offers control of your media player/center with TV-style Remote Control Unit via standard IrDA port IrDA Remote Control offers control of your media player/center with TV-style Remote Control Unit via standard IrDA (infrared) port.
Main features:
- No additional hardware required (only standard IrDA port)
- Flexible adjustments for most existed Remote Control Units
- Simplicity of Remote Control training
System requirements:
Remote Control Unit Requirements
As the IrDA (infrared port) and TV Remote Control Unit (RCU) have completely different nature:
- There are some RCU will not work with the program at all. As there is no strict standards for RCU data type and data transfer protocol, there is no abilities to predict capacity for work of an RCU in advance. Usually you have several RCUs available and, therefore, have the ability to choose right RCU.
- Some RCUs have no full scale ability for repeating commands of pushed buttons. In that case, you should emulate command repeats manually by multiple separate key presses.
- Remote control distance of IrDA Remote Control may be lower than habitual one. It depends on how precisely you direct your RCU to IrDA (infrared) receiver. If the IrDA receiver is located on side of rear panel (in some notebooks) you can use mirror to redirect the RCU infrared beam onto IrDA receiver.
IrDA Receiver Requirements
- Only embedded IrDA receivers are compatible (usually in notebooks). External COM port based IrDA receiver may work, USB connected IrDA receivers are not compatible at least in the current version.
- Your computer should have no other active (logically connected/active) serial ports (COM ports) except IrDA. Otherwise, IrDA port will not be detected correctly. In that case, you can set IrDA port device address manually (in the Settings dialog) or close the connection and re-run the program to repeat automatic detection.
- IrDA device must be properly configured and work. IrDA Remote Control does not allow simultaneous IrDA transmitting, which can cause random remote control behavior. Sometimes to restore genuine IrDA functionally exiting the program is not enough, reboot may be required.
- IrDA device must be SIR type. It means UART based with maximum speed less or equal to 115200 kbit/sec. You can verify IrDA speed in the "Device Manager" of your Windows or simply by trying the program.

Resident Tray System software for barcode scanner or other serial data capture devices that have a standard RS232 interface.
Bill Redirect Serial COMPort to Keyboard is a software that scans barcode capture serial data.
The program will redirect serial inputs from COM ports to keyboard buffer on your computer, as if the data were directly typed in from the keyboard.
Main features:
- Debugger
- System Tray running
- Macro Commands
- Mouse control
- Prefix Suffix
- AZERTY or QWERTY keyboard
- Control multiple serial or TCP Ethernet ports
- Support RS232 Storm Keypads
- Password protected configuration
- Upper case option
- Search and replace characters
- Specific ASCII Characters removing feature
- Windows API keyboard 32 Buffer or OCX
- Sends data to default or specific application (POS, database, Excel, Word, or your own customized software)
- Generate actions in your PC via your serial port
- (external remote switch on pin CTS & DSR )
This download is marked as adware because it displays advertisement banners or other type of commercials while running.

Virtual Drum 1 is powerful audio recording tool which makes Drum loops with a innovator interface. Does not requires musical knowledge. The user can easily to copy and to tranfer Patterns, to control the BPM, the resolutions and the sound banks.